before and after, or this morning and afternoon

[hummer74]

Originally Posted by SHYANNE

so what size toyos are you running on the stock wheel ?

are you asking me? if you are, i am running 37 inch tires. official spec of the tire is 37X13.5X17, and yes it's the stock wheel just powdercoated black. the powdercoating cost me $55 a wheel.

and thanks dennis.

[GLBLWARMR]

Originally Posted by DennisAJC

That is one awsome transformation.

He has done a great job with it.

[hummer74]

thanks again everyone.

well here's an update. my buddy owns a firetruck shop in denton and he helped me out with moving the airbag sensor and cutting the lip on that one piece. here a some pics showing the final product, i havent painted the shiny parts yet.

[hummer74]

we went ahead and flipped the lower part as well, that was VERY easy. actually, we swapped the the whole arms from the left side of the vehicle to the right and vice versa. turned out great and lots more clearance. all in all, took about 30 minutes to do all of it.

[H2 BULLY]

Awesome, what size and type of Screw did you use for both the top and bottom?

[hummer74]

Originally Posted by H2 BULLY

Awesome, what size and type of Screw did you use for both the top and bottom?

lol, i knew someone would ask. to be honest i have no idea. but it really didn't matter, because, you need to cut the remaining plastic post off, you can drill any size hole you want into the arm and put whatever size you want in there. i actually didn't even use a screw, we used a phillips head domed bolt and locknut. you just drill the hole to whatever size you are going to use. and for the bottom, you use the stock bolt thats already on there. hope that helps. if you have any questions when you are doing it, i can pm you my phone number to walk you through it.

[hummer74]

HOPE THIS HELPS. I CAN USE PAINT TOO DOC!

[obzidian]

truck looks great.... you think you could possibly just reuse that hard plastic pin that comes with the sensor or you had no choice to modifiy it?

[hummer74]

Originally Posted by obzidian

truck looks great.... you think you could possibly just reuse that hard plastic pin that comes with the sensor or you had no choice to modifiy it?

yes, if you can figure out how to get if off without breaking it. i just didnt want to mess with it, so we cut if off.

[hummer74]

ok, i found out what the bolt is.

it is a 5/16 stainless steel x 1.250 phillips panhead bolt with a stainless steel nylock nut. that bolt fits perfectly through the rubber link. hope that helps you all.

[H2 BULLY]

Thanks I am going to do the switch some time this week.

[Sportsdude]

Nice rig

[hummer74]

thanks sports dude.

h2bully, be sure to post up some pics when youre done!

[H2 BULLY]

DONE My hubby did a little how to with pics, it is in the H2 tech discussion.

[Bully13]

Originally Posted by H2 BULLY

DONE My hubby did a little how to with pics, it is in the H2 tech discussion.

http://www.elcovaforums.com/forums/s...ad.php?t=24657

[mrlittle]

what model number are those piaa's and did they wire into old lights harness?

[hummer74]

Originally Posted by mrlittle

what model number are those piaa's and did they wire into old lights harness?

i believe they are the piaa 520's but dont quote me on that. install was simple if u have factory wiring already there. just cut the old plugs from the old lights and solder on the piaa plugs and then wrap up the connection. that was it. i had mine done at cartoys for me, it was like $50 or something....pretty cheap and they did a better job than i would have.

[H2BRUTE]

Looks like one bad H2..Great job. Especially like the pic from ground level showing off them monster tires...Love the H2. You can personalize it to your hearts content and most of the time, they look great whether you are a blinger or off roader......Da Brute