|
#1
09-03-2003, 09:50 AM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
I have seen several H1's and H2's (off-road run videos) with large US Flags mounted from the rear of the vehicles and would like to do so for parades, special events. (I have an H2)
Can any of you post pics/info on mounting them?
I'm thinking of those with the flag pole holding the flag at near vertical.
Ric
OMAHOG/IHOG
Hum2@cox.net
#2
09-03-2003, 09:50 AM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
I have seen several H1's and H2's (off-road run videos) with large US Flags mounted from the rear of the vehicles and would like to do so for parades, special events. (I have an H2)
Can any of you post pics/info on mounting them?
I'm thinking of those with the flag pole holding the flag at near vertical.
Ric
OMAHOG/IHOG
Hum2@cox.net
#4
09-03-2003, 10:32 AM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
Thanks Phil!
That's kind of what I was thinking of...Did you make it yourself or can it be purchased cheaply? :-)
Ric
OMAHOG/IHOG
Hum2@cox.net
#6
09-03-2003, 11:41 AM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
#7
09-03-2003, 11:48 AM
Hummer Expert
Join Date: Jul 2003
Location: PA
Posts: 515
#8
09-03-2003, 11:59 AM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
#9
09-03-2003, 12:57 PM
Join Date: Feb 2003
Location: indianapolis/Cincinnati
Posts: 268
http://www.leftysautomotive.com/acce...ssoryMisc3.htm
"Be who you are and say what you feel because those who mind don't matter and those who matter don't mind"
#11
09-03-2003, 01:26 PM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
#12
09-05-2003, 10:58 AM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
I have a cheap fix....1" dia copper piping 18" long. Smashed 3 inches on one end in a vice, bent it at 90 degrees. Will drill a couple holes to screw/bolt the flat spot to a 2X4, 8" long, then, bolt the 2X4 to the trailer hitch. Flag pole slides into the copper piping.
Ric
OMAHOG/IHOG
Hum2@cox.net
#14
09-05-2003, 03:56 PM
Hummer Expert
Join Date: Nov 2002
Location: Omaha, NE
Posts: 631
Hey Joyce:
I just started the idea this AM before work (just bent the pipe). I was thinking about buying a 1" bit to drill a hole that matched the ball mount hole and bolt there, then I thought I might mount it to a 2X4 and bolt the 2X4 to the hitch ball mount.
I will post pics when I get time to play with this. I'm sure there are other possibilities. The Lefty's unit (http://www.leftysautomotive.com/acce...ssoryMisc3.htm) is pretty good as well. (but $40).
Ric
OMAHOG/IHOG
Hum2@cox.net
«
Previous Thread
|
Next Thread
»
Thread Tools
Search this Thread
Display Modes
Posting Rules
All times are GMT +1. The time now is 03:27 PM.
Linear Mode
