Hummer Forums by Elcova  
Forums - Home
Source Decals

Source Motors
Custom. Accessories.

H2 Accessories
H3 Accessories
Other Vehicles

H2 Source

H2 Member Photos
H2 Owners Map
H2 Classifieds
H2 Photo Gallery
SUT Photo Gallery
H2 Details

H2 Club

Chapters
Application

H3 Source

H3 Member Photos
H3 Classifieds
H3 Photo Gallery
H3 Owners Map
H3 Details
H3T Concept

H1 Source

H1 Member Photos
H1 Classifieds
H1 Photo Gallery
H1 Details

General Info

Hummer Dealers
Contact
Advertise

Sponsored Ads










 


Source Motors - custom. accessories.


Go Back   Hummer Forums by Elcova > Hummer H2 Discussion Forums > General H2 Discussion

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-09-2006, 01:36 PM
89vette 89vette is offline
Hummer Professional
 
Join Date: Jul 2003
Location: Export, PA
Posts: 295
89vette is off the scale
Default

Both my O3 and my 05 had been plagued by cheap squeaky plastic door panels that bug the hell out of me. I did some research on this site and some people mentioned some updated clips. I took mine in for service 3 weeks ago to have these squeaks addressed. They applied about 2 inches of clear anti-noise tape where the panel edge meets the metal on the door. A week later they were squeaking again. In addition, they did not address the squeaks around the trim piece that is around the window buttons or the trim around pull handle (not the removable trim piece but the entire trim piece).

If you remove the panel, you will see these two trim pieces are attached and then melted on in a few areas. If you flex the panel, it squeaks where there is plastic to plastic contact. What I did was apply a medium viscosity super glue down inside all of these areas to stop the movement. You have to be careful because the glue can easily ooze out to the external areas of the panel. I also removed the door window switch gear and applied some small pieces of felt to the under side to tighten it up and stop it from moving all around. Also I wrapped some electrical tape around the whole unit and then popped it back into the trim bezel to further eliminate plastic to plastic contact. On all the edges of the panel, I attached electrical tape where it meets the door metal.

Now the panel is solid. You can hold the grab handle and pull it back and forth with no squeaks. You can rest your arm on it and also not have any squeaks.
Reply With Quote
  #2  
Old 01-09-2006, 01:36 PM
89vette 89vette is offline
Hummer Professional
 
Join Date: Jul 2003
Location: Export, PA
Posts: 295
89vette is off the scale
Default

Both my O3 and my 05 had been plagued by cheap squeaky plastic door panels that bug the hell out of me. I did some research on this site and some people mentioned some updated clips. I took mine in for service 3 weeks ago to have these squeaks addressed. They applied about 2 inches of clear anti-noise tape where the panel edge meets the metal on the door. A week later they were squeaking again. In addition, they did not address the squeaks around the trim piece that is around the window buttons or the trim around pull handle (not the removable trim piece but the entire trim piece).

If you remove the panel, you will see these two trim pieces are attached and then melted on in a few areas. If you flex the panel, it squeaks where there is plastic to plastic contact. What I did was apply a medium viscosity super glue down inside all of these areas to stop the movement. You have to be careful because the glue can easily ooze out to the external areas of the panel. I also removed the door window switch gear and applied some small pieces of felt to the under side to tighten it up and stop it from moving all around. Also I wrapped some electrical tape around the whole unit and then popped it back into the trim bezel to further eliminate plastic to plastic contact. On all the edges of the panel, I attached electrical tape where it meets the door metal.

Now the panel is solid. You can hold the grab handle and pull it back and forth with no squeaks. You can rest your arm on it and also not have any squeaks.
Reply With Quote
  #3  
Old 01-09-2006, 03:20 PM
H2Finally's Avatar
H2Finally H2Finally is offline
Hummer Authority
 
Join Date: Jan 2004
Location: Home is where the H2 is..
Posts: 1,814
H2Finally is an unknown quantity at this point
Default

How difficult is it to remove the door panels? I want to add soundproofing, but afraid of breaking anything.
__________________
Can BLING Get You Home?
Reply With Quote
  #4  
Old 01-09-2006, 04:22 PM
89vette 89vette is offline
Hummer Professional
 
Join Date: Jul 2003
Location: Export, PA
Posts: 295
89vette is off the scale
Default

It is not difficut at all. There is one screw to remove the door handle latch cover. Behind that are two screws (8mm if I remember correctly) that you will have to take out. After that, it unsnaps but be careful or you might break of the mounting locations for the clips.
Reply With Quote
  #5  
Old 01-09-2006, 04:31 PM
H2Finally's Avatar
H2Finally H2Finally is offline
Hummer Authority
 
Join Date: Jan 2004
Location: Home is where the H2 is..
Posts: 1,814
H2Finally is an unknown quantity at this point
Default

Thanks! Gotta do this soon before I get TOO BUSY with WORK!!
__________________
Can BLING Get You Home?
Reply With Quote
  #6  
Old 01-09-2006, 05:10 PM
TXSUT's Avatar
TXSUT TXSUT is offline
Hummer Authority
 
Join Date: Oct 2004
Location: Houston, TX
Posts: 1,290
TXSUT is an unknown quantity at this point
Default

Thanks for the tips!!!
Reply With Quote
  #7  
Old 01-09-2006, 06:09 PM
Dan Dan is offline
Hummer Guru
 
Join Date: Nov 2002
Location: Cognito
Posts: 2,155
Dan is an unknown quantity at this point
Default

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by TXSUT:
Thanks for the tips!!! </div></BLOCKQUOTE>

TIPS!!!
Reply With Quote
  #8  
Old 01-09-2006, 06:20 PM
TXSUT's Avatar
TXSUT TXSUT is offline
Hummer Authority
 
Join Date: Oct 2004
Location: Houston, TX
Posts: 1,290
TXSUT is an unknown quantity at this point
Default

<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by Dan:
<BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by TXSUT:
Thanks for the tips!!! </div></BLOCKQUOTE>

TIPS!!! </div></BLOCKQUOTE>

Look Dan, I already have enough problems with your posts...you see, my computer at work is screwed up, and takes forever to load your avatar fully. So, for much too long, whenever I'm viewing any of your posts, I have this 2.5"x2.5" picture of a hot, oily woman massaging her nice, big tits on my screen! LMAO!
Reply With Quote
  #9  
Old 08-17-2023, 07:28 PM
89vette 89vette is offline
Hummer Professional
 
Join Date: Jul 2003
Location: Export, PA
Posts: 295
89vette is off the scale
Default Re: Super glue fix for squeaky door panels

There is nothing like buying another H2 after 17 years and searching how to fix squeaky door panels and finding your own post from 2006!
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 04:12 PM.


Powered by vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.