 |
|
11-30-2002, 04:27 PM
|
|
|
|
Join Date: Nov 2002
Location: San Diego, CA, USA
Posts: 31
|
|
My SMA tire carrier rattles over bumps. Everything appears to be mounted correctly, I guess it is just the play in the carrier. It was driving me crazy last weekend at the desert! If others don't rattle, maybe mine is too far out of tolerances.
Thanks, Jim Lake.
|
11-30-2002, 04:27 PM
|
|
|
|
Join Date: Nov 2002
Location: San Diego, CA, USA
Posts: 31
|
|
My SMA tire carrier rattles over bumps. Everything appears to be mounted correctly, I guess it is just the play in the carrier. It was driving me crazy last weekend at the desert! If others don't rattle, maybe mine is too far out of tolerances.
Thanks, Jim Lake.
|
11-30-2002, 07:12 PM
|
|
|
|
Join Date: Nov 2002
Location: Washington...State...NOT D.C.
Posts: 13
|
|
I went to the hills yesterday and mine was rattling too. Drove me nuts. Must be in the latch area. Am going to see what I can do about it later today and post results.
|
11-30-2002, 09:36 PM
|
|
|
|
Join Date: Nov 2002
Location: long island
Posts: 214
|
|
was that easy to put on have herd something about the wires for the plate that you have to cut a certien color [img]/infopop/emoticons/icon_eek.gif[/img]
__________________
03/sunset orange supercharged & custom programed-- gale banks monster exhaust
|
12-01-2002, 04:03 AM
|
|
|
|
Join Date: Nov 2002
Location: San Diego, CA, USA
Posts: 31
|
|
Huh?
|
12-01-2002, 04:15 AM
|
|
|
|
Join Date: Nov 2002
Location: Long Island, NY
Posts: 48
|
|
Mine was rattling and driving me crazy! It's where the part of the tire carrier goes into the left side bracket. Everytime you go over a bump, the part that holds the tire bounces up and down hitting the top and bottom of the inside of the bracket. I fixed mine by shaving down and gluing rubber bumpers on the top and bottom of the bracket ( where the locking pin fit's in). Make sure it's a snug fit between the carrier bar and the bumpers. 3000 miles later...still no noise and never fell off. Good luck on yours! [img]/infopop/emoticons/icon_wink.gif[/img]
|
12-01-2002, 04:19 AM
|
|
|
|
Join Date: Nov 2002
Location: Long Island, NY
Posts: 48
|
|
Hey H2Fan??? [img]/infopop/emoticons/icon_confused.gif[/img] It's easy to put on and the wire for the license plate light just splices onto to trailer wiring. If you need help, My husband is around to help you. Just give us a shout out! We live in Rockville Centre
|
12-01-2002, 10:03 AM
|
|
|
|
Join Date: Nov 2002
Location: long island
Posts: 214
|
|
h2girl thank you very much for the help just might do that pacing the floor right now [img]/infopop/emoticons/icon_biggrin.gif[/img] due date monday [img]/infopop/emoticons/icon_biggrin.gif[/img] [img]/infopop/emoticons/icon_biggrin.gif[/img]
__________________
03/sunset orange supercharged & custom programed-- gale banks monster exhaust
|
12-01-2002, 10:56 AM
|
|
|
|
Join Date: Dec 2002
Location: southlake, tx usa
Posts: 115
|
|
the dealer installed mine and the guys put what looked like adhesive backed rubber pads in the receiver slot for the cross bar(top and bottom). Mine fits very snugly, no rattle at all.
|
12-01-2002, 02:12 PM
|
|
|
|
Join Date: Nov 2002
Location: San Diego, CA, USA
Posts: 31
|
|
Good tips - I'll try it out today.
Thanks.
|
12-01-2002, 03:55 PM
|
 |
Hummer Expert
|
|
Join Date: Nov 2002
Location: Phoenix Arizona
Posts: 745
|
|
I cut a old bikecycke intertube and put over the are were the locking pen goes thru, no more noise
|
12-01-2002, 05:21 PM
|
|
|
|
Join Date: Nov 2002
Location: In the Deep South, Along the Shore of the Flint River
Posts: 442
|
|
yes mine rattles like that...did not notice until after my off roading adventure...
gonna try the rubber bumper thing....that may just do the trick!!!
~amy
Reality is merely a crutch for those with a broken imagination.~anon.
__________________
~amy
White 2003 H2
Got Soap?
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +1. The time now is 10:50 PM.
|
