Seats no power?

Navigator · #1 02-18-2005, 08:17 PM

My 2 front seats no longer heat or power in any direction. I checked the fuse and its fine. Any Suggestions? I tried the search function but it said something about an error & that eve was still processing a previous request

Navigator · #2 02-18-2005, 08:17 PM

My 2 front seats no longer heat or power in any direction. I checked the fuse and its fine. Any Suggestions? I tried the search function but it said something about an error & that eve was still processing a previous request

PARAGON · #3 02-18-2005, 10:44 PM

In the fuse box under the hood also check the fuse MBEC1 in the top row.

Navigator · #4 02-23-2005, 12:27 AM

All the fuses are good still no power or heat

timgco · #5 02-23-2005, 12:39 AM

Without the FIND funtion operating, I can't pull up the post. I though it was a bad module under the seat. Wasn't there a TSB on the 03's a while back? I thought so. Anyhow, say hello to Bergstrom's off-road track for me when you take her in... if you do.

PARAGON · #6 02-23-2005, 02:00 AM

The problem is that it is happening on both front seats, 2 separate seat modules (I think). So my though was that it would be upstream from there. I'll look again.

PARAGON · #7 02-23-2005, 02:17 AM

<Table>
<H1>Seat
Heater and/or Memory Power Seat Inoperative (Replace Memory Seat Control Module)
#03-08-50-003 - (Jan 21, 2003) </H1>
Seat Heater and/or
Memory Power Seat Inoperative (Replace Memory Seat Control Module) 
2003 Cadillac
Escalade, Escalade ESV, Escalade EXT 
2003 Chevrolet
Avalanche, Silverado, Suburban, Tahoe 
2003 GMC Sierra,
Yukon, Yukon XL, Yukon Denali, Yukon Denali XL 
2003 HUMMER H2

<DIV class=Sect>
<H2>Condition </H2>
Some customers may
comment that the seat heater and/or memory seat functions are inoperative.
</DIV>
<DIV class=Sect>
<H2>Cause </H2>
A logic lockup of
the memory seat control module may cause this condition. </DIV>
<DIV class=Sect>
<H2>Correction </H2>
Important 
This repair is not to be performed on vehicles without
memory/heated seats. If the vehicle does not have memory/heated seats but has an
inoperative power seat, use published Service Information to diagnose the
concern. 
If the seat is currently inoperable, perform the
following diagnostic steps to determine if replacement of the memory seat
control module is the correct repair:

<LI>Connect a Tech 2® to the vehicle and monitor
the parameters in the sensor data list for the driver seat module as you try to
move the seat. Are the displayed data parameters changing, or does the Tech 2®
display no communication as the seat switch is moved to various positions? If
the data parameters do not change, the memory seat control module may be
inoperative due to a logic lockup. 
<LI style="LINE-HEIGHT: 18px">Remove the SEAT
circuit breaker in the instrument panel relay block located under the left side
of the instrument panel next to the parking brake. This circuit breaker also
supplies power to the passenger seat. 
<LI>Verify that the circuit breaker is not open. If
it is not open, wait 30 seconds and then reinstall the circuit breaker. 
<LI style="LINE-HEIGHT: 18px">Try to move the seat
again. 
<LI>If the seat moves or the data parameters
displayed on the Tech 2® change when the seat switch is activated, replace the
memory seat control module. Use the Memory Seat Control Module Replacement
procedure in SI. 
<LI>If the memory seat is still inoperative, use
normal Service Manual diagnostics to determine the cause of this condition.
</LI>

Service Information
Page 2
of 2

Parts
Information
[img]images/seat inoperative_img_0.jpg[/img]
Parts are currently
available from GMSPO. </DIV>
<DIV class=Sect>
<H2 style="TEXT-ALIGN: justify">Warranty
Information
</H2>
For vehicles repaired under warranty, use:
[img]images/seat inoperative_img_1.jpg[/img]</DIV></Table>

funpilot · #8 02-23-2005, 11:34 AM

Paragon, I hope you become just as knowledgeable on issues regarding the H3 for those of us who will purchase it. Oh great guru, we bow to the east......

4churchill · #9 02-24-2005, 02:44 AM

my heated seats stopped working on my truck today, i just turned the ignition off removed the key and turned the truck back on and the started to work, i think my situation was just a little glitchy glitch

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode