Torsion Bar Information

[humdoug]

The stock shocks are still on but the extension piece was added to lower shock bolt so the shocks work properly with the extra lift.

Wife still having a hard time getting in.

[Killer]

I too have the Truxxx kit installed and also previously had the torsion bars cranked. I speak from experience...the ride with the Truxxx kit is the same as the original ride from the factory. Not sure about any of you guys but the ride with the torsion bars "cranked" up was starting to get on my nerves and was very rough in comparison to that of the Truxxx lifted version of my H3. The price may seem steep but in IMHO it was money well spent as I now enjoy driving the H3 much more than I did when it "jarred" at every uneven section in the highway.

[H3.007]

I had my torsion bars adjusted this weekend by a garage that does professional alignments for individuals as well as many of the local delaerships. The system they used has digital cameras, IR sensors, and wheel mounted reflectors that measure the usual (caster, camber, etc. etc.). The system keeps a record of all adjustments for fine tuning or complete reversal.

The mech that did the work felt that the factory alignment was not correct from the get go. He spent about an hour and a half on the alignment and torsion bar adjustment. Total height adjustment was around three inches in the front and it now sits level. However, he had to adjust the torsion bars many more times than the two or three often spoke of on here. He also said that he wants to see it in 7,000 miles (10,000 mark) to check for settling. Perhaps every H3 is a bit different?

Regardless, after 100 miles of driving both highway and street conditions, ride quality is tighter with less sway. Overall, I'd say it was worth the $40. I will post if I see any unusual wear on parts or tires.

[usetosellhummer]

One good off road trip will blow that all to hell

[H3.007]

Anyone else with the torsion bar adjustment "blow it all to hell" after off-roading?

[Sewie]

Originally Posted by H3.007

Anyone else with the torsion bar adjustment "blow it all to hell" after off-roading?

I think he was referring to the alignment. And yes, I've blown the alignment all to hell offroad.

[MountainBlue]

Originally Posted by H3.007

I had my torsion bars adjusted this weekend by a garage that does professional alignments for individuals as well as many of the local delaerships. The system they used has digital cameras, IR sensors, and wheel mounted reflectors that measure the usual (caster, camber, etc. etc.). The system keeps a record of all adjustments for fine tuning or complete reversal.

The mech that did the work felt that the factory alignment was not correct from the get go. He spent about an hour and a half on the alignment and torsion bar adjustment. Total height adjustment was around three inches in the front and it now sits level. However, he had to adjust the torsion bars many more times than the two or three often spoke of on here. He also said that he wants to see it in 7,000 miles (10,000 mark) to check for settling. Perhaps every H3 is a bit different?

Regardless, after 100 miles of driving both highway and street conditions, ride quality is tighter with less sway. Overall, I'd say it was worth the $40. I will post if I see any unusual wear on parts or tires.

Everyone is slightly different. With mine, the driver's side was way off from the factory. I did 2.5 turns on the passanger side and had to 5.5 turns on the drivers side to get the ride height the same. I only went up about 1.5" and will see how it feels. Then take it in for tires and alinment.

[Sewie]

Originally Posted by H3.007

Total height adjustment was around three inches in the front and it now sits level. However, he had to adjust the torsion bars many more times than the two or three often spoke of on here.

Not everyone went for "level." I only wanted 1-1.5" of lift so mine were only turned a couple times.