For Dochummer

[CO Hummer]

Inner Shaft and/or Housing Replacement - Front Drive Axle

<A href="http://127.0.0.1:9001/servlets/BlobShtml?ShtmlFile=839921&evc=sm&pubid=293&cellId =47600&mspsdsubkey=2186#ss1-839921">Removal Procedure

1. <LI type=1>Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. <LI type=1>Drain the front drive axle. Refer to Lubricant Replacement - Front Drive Axle .
   
   
   <LI type=1>Remove the right wheel drive shaft inboard flange bolts from the inner axle shaft. <LI type=1>Disconnect the right wheel drive shaft from the inner axle shaft.
   
   
   <LI type=1>Disconnect the inner axle shaft from the differential case side gear using a hammer and brass drift.
   
   
   <LI type=1>Remove the inner axle shaft housing nuts from the bracket.
   
   
   <LI type=1>Remove the inner axle shaft housing bolts from the differential carrier assembly. <LI type=1>Remove the inner axle shaft and inner axle shaft housing from the vehicle. <LI type=1>Remove the inner axle shaft from the inner axle shaft housing.
2. Remove the inner axle shaft seal and the bearing from the inner axle shaft housing. Refer to Inner Axle Seal and/or Bearing Replacement - Front Drive Axle .

<A href="http://127.0.0.1:9001/servlets/BlobShtml?ShtmlFile=839921&evc=sm&pubid=293&cellId =47600&mspsdsubkey=2186#ss2-839921">Installation Procedure

1. <LI type=1>Install the new inner axle shaft bearing and the new seal to the inner axle shaft housing. Refer to Inner Axle Seal and/or Bearing Replacement - Front Drive Axle . <LI type=1>Install the inner axle shaft into the inner axle shaft housing. Do not install the inner axle shaft completely into the inner axle shaft housing at this time. <LI type=1>Apply sealant GM P/N 1052942 (Canadian P/N 10953466) or equivalent to the inner axle housing to differential carrier sealing surface. <LI type=1>Install the inner axle shaft and the inner axle shaft housing to the differential carrier assembly.
   
   
   
   Notice
   
   Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
   
   <LI type=1>Install the inner axle shaft housing bolts. Tighten Tighten the inner axle shaft housing bolts to 40 N?m (30 lb ft).
   
   
   
   <LI type=1>Install the inner axle shaft housing nuts to the bracket. Tighten Tighten the inner axle shaft housing nuts to 100 N?m (75 lb ft).
   <LI type=1>Install the inner axle shaft into the differential case side gear by doing the following:
   1. <LI type=A>Turn the inner axle shaft and align the splines of the inner axle shaft with the splines on the differential side gear. <LI type=A>Drive the inner axle shaft into the differential case side gear assembly using a soft-faced mallet until the retaining ring on the inner axle shaft is fully seated within the groove in the differential case side gear.
   2. Pull back on the inner axle shaft to ensure that the inner axle shaft is properly retained in the differential case side gear.
   <LI type=1>Install the right wheel drive shaft to the inner axle shaft.
   
   
   <LI type=1>Install the right wheel drive shaft inboard flange to inner axle shaft bolts. Tighten Tighten the wheel drive shaft inboard flange to inner axle shaft bolts to 79 N?m (58 lb ft).
   <LI type=1>Fill the front axle with axle lubricant. Use the proper fluid. Refer to Fluid and Lubricant Recommendations and Capacities - Approximate Fluid in Maintenance and Lubrication.
2. Lower the vehicle.