Tire Pressure for 35" tires?

[fourfourto]

I would guess 35 to 40 lbs would be fine
But wouldnt the best way to find out is ask the person you bought the tires from..Shouldnt they know based on tire and wieght of truck.

[H3.007]

My rubbers say Trojan on them and nothing about pressure..... and the treads are perpedicularly aligned to the "road".

I am soooooooooo confused......

[SR1355]

Originally Posted by H3.007

My rubbers say Trojan on them and nothing about pressure..... and the treads are perpedicularly aligned to the "road".

I am soooooooooo confused......

LMAOROF.....

[RubHer Yellow Ducky]

Originally Posted by fourfourto

I would guess 35 to 40 lbs would be fine
But wouldnt the best way to find out is ask the person you bought the tires from. NO ! .Shouldnt they know based on tire and wieght of truck.

Most salespeople don't know "CHIT from SHINOLA" ...
be an educated consumer and look up the information
HELL I went to "A" HUMMER DEALER this year and one of the salespeople didn't know the H-3 had a 5 cylinder in it...

[fourfourto]

Originally Posted by RubHer Yellow Ducky

Most salespeople don't know "CHIT from SHINOLA" ...
be an educated consumer and look up the information
HELL I went to "A" HUMMER DEALER this year and one of the salespeople didn't know the H-3 had a 5 cylinder in it...

The H3 has a 5 cylinder in it Are you sure


I say just put in 37.5 PSI and be done with it.

[KeyzH3]

Originally Posted by RubHer Yellow Ducky

Most salespeople don't know "CHIT from SHINOLA" ...
be an educated consumer and look up the information
HELL I went to "A" HUMMER DEALER this year and one of the salespeople didn't know the H-3 had a 5 cylinder in it...

Got that right! This will be one of two firsts for my tire guy. First H3 and first 35s. Speaking of Dumass dealers, I just noticed that my dealer butcherd up my fuse/breaker box with a screwdriver, breaking off all the tabs. But they did it back in February, going to be hard to prove it now. Unless it happened at the factory

[RubHer Yellow Ducky]

Originally Posted by KeyzH3

Got that right! This will be one of two firsts for my tire guy. First H3 and first 35s. Speaking of Dumass dealers, I just noticed that my dealer butcherd up my fuse/breaker box with a screwdriver, breaking off all the tabs. But they did it back in February, going to be hard to prove it now. Unless it happened at the factory

KeyZ,

Where did you buy yours and where do you get it serviced ?

I purchased both of mine at VERA but get them serviced at Williamson(lots closer) Service writter is Mike Sutherland. He bends over backwards to help...

[Desert Dan]

The max PSI on tires is the pressure you should be running when the tire is at it's max weight limit.

There is no need to run 40-50 psi (in the H3's) when empty around town unless you want to beat your self up with a rough ride.

If my truck is fully loaded and I have a long highwy trip I may put 45psi in the tires. This is for load capacity, mileage, to reduce heat build up, better handling and safety.

[KeyzH3]

Originally Posted by RubHer Yellow Ducky

KeyZ,

Where did you buy yours and where do you get it serviced ?

I purchased both of mine at VERA but get it serviced at Williamson(lots closer) Service writter is Mike Sutherland. He bends over backwards to help...

Palm Beach Hummer, and it never been to any other shop for service since I bought it, only a local GM dealer that reset the tire senders before I had figured it out.

[marin8703]

hey sorry to bring this thread back but got a question for those unning 35 toyo open country mt. I got my tires installed about a week ago and i've noticed that only the center of the tire makes contact with the ground. Its as if its over inflated. But it cant be over inflated because i ran them at 32-33 psi.

i know as they wear it will even out, but then the wear wont be even. Does anyone remember if this is how thier's were when they were new?

any advice?

thanks.

[Sewie]

Mine did that........but they were overinflated.