Need to buy a wiper motor and module. Where from?

[twr]

Hi your welcome. I have bought from them before with no problems. If you call them ask for INTERNET PARTS SALES and talk to John Z that is who i deal with, he is very nice. They may not have it in stock but can usally get stuff in a week or so.

[BLUETHUNDER]

Well i ordered the part today. Cover including the circuit board. Cost was $72.Hopefully this should sort my wiper problems. TWR thanks for the link.

[twr]

Hi did you phone and talk to John or just order on the internet?

[kmleong]

Originally Posted by BLUETHUNDER

Well i ordered the part today. Cover including the circuit board. Cost was $72.Hopefully this should sort my wiper problems. TWR thanks for the link.

I think that i have the same problem as you, same symptoms anway. Do you have a part number? I looked on the link and came up with $188.44

[BLUETHUNDER]

Yeah sure. Its #19120103. It should list it as cover. I had a confirmation e-mail back to ay it was for cover including (circuit board).

[kmleong]

Thanks Bluethunder, I did a little further checking on this.
GM Parts Direct sells at $58.32.
GM Parts Worldwide sells at $71.47 & $48.00 S/H for a total of $119.47.
Locally I got it for $155.68 CDN., taxes in from the dealer because I couldn't wait for 4 - 21 days for GM Parts Worldwide. The new part has a thicker gasket. I had great difficulty in getting it compressed enough to get the latches to catch. Hopefully it works this time.

[BLUETHUNDER]

Just an update on this. Finally got around to fitting the new circuit board yesterday. All the problems are now solved and everything is back to normal

[PaHumBug]

Blue Thunder,
I can't find the cover and circuit board. What website and what part number did you use? I've dried out and resealed mine twice, but my wipers only work when it's NOT raining (of course), so I'm going to replace my circuit board.

[Biskxp]

Just had my rear washer go nuts too - Read through the thread - grabbed some tools and went to work.

Had a bit of moisture build up on the pcb cleaned it up but still had the same problem with the rear washer pump running continiously. New PCB time....

However being totally bloodyminded I took the board out of the cover, cleaned it again and dug a multimeter out..........

And the findings are.......

One resistor at the bottom of the board had water damage and had dropped from about 380 Ohms to 11 Ohms which instantly engaged the wash relay on the underside of the board.



Stole a pic and marked the resistor.

Removed resistor and all now works perfectly though one day I suppose I ought to get round to putting in a replacement.

Due to the location of the resistor I imagine this is the main cause of the washer going nuts so I hope it helps some people

[Easy Ed]

Biskxp, You didn't steal it you improved it

Thanks for the heads up on the resistor, I would not have figured it out

Ed

[BLUETHUNDER]

Originally Posted by Biskxp

Just had my rear washer go nuts too - Read through the thread - grabbed some tools and went to work.

Had a bit of moisture build up on the pcb cleaned it up but still had the same problem with the rear washer pump running continiously. New PCB time....

However being totally bloodyminded I took the board out of the cover, cleaned it again and dug a multimeter out..........

And the findings are.......

One resistor at the bottom of the board had water damage and had dropped from about 380 Ohms to 11 Ohms which instantly engaged the wash relay on the underside of the board.

Attachment 53209

Stole a pic and marked the resistor.

Removed resistor and all now works perfectly though one day I suppose I ought to get round to putting in a replacement.

Due to the location of the resistor I imagine this is the main cause of the washer going nuts so I hope it helps some people

Thanks for the tip.did you remove it completely???.

[Biskxp]

Yeah removed it completely. 2 second job with a soldering iron. Just been for a drive and all seems to be working no problems now!