Removing air suspension, replacing with coils

[fyr145]

Thats what I was wondering, I have the spring set up but got the compressor to have on board in case I needed air for my tires or any other inflatable goodies and just use it for that alone.

Egan,

If you arent going to use your old harness, is there anyway that I could get it from you so I could use it for this purpose?

fyr145

[Egan]

Originally Posted by fyr145

Thats what I was wondering, I have the spring set up but got the compressor to have on board in case I needed air for my tires or any other inflatable goodies and just use it for that alone.

Egan,

If you arent going to use your old harness, is there anyway that I could get it from you so I could use it for this purpose?

fyr145

It looks like the wiring on the truck joins up with a much larger wiring loom at the bumper and then runs to the front of the H2. Pulling out just the air controls may be difficult. As for the wiring at the compressor end, I have it all pulled apart and you're welcome to any of it.

In fact, if anyone needs spare parts (compressor x2, tank, airbags x2) let me know.

[RJ03]

How much would you want for the air compressor assembly? Thanks, RJ

[Easy Ed]

Pulled all mine out in 2007

http://www.elcovaforums.com/forums/attachment.php?attachmentid=36217&stc=1&d=11712447 65

Link to post http://www.elcovaforums.com/forums/s...ad.php?t=24471

[fyr145]

Originally Posted by Egan

It looks like the wiring on the truck joins up with a much larger wiring loom at the bumper and then runs to the front of the H2. Pulling out just the air controls may be difficult. As for the wiring at the compressor end, I have it all pulled apart and you're welcome to any of it.

In fact, if anyone needs spare parts (compressor x2, tank, airbags x2) let me know.

I need the wiring at the compressor end that it plugs into. It looks like is a 24 pin connection and theres another smaller 2 pin connector near it as well. You show it in one of your pics that says you zip tied it to the rear bumper.

Do you still have the bolts to the compressor too, so that I can get mine mounted?

Let me how much shipping is and I can send you payment via Paypal.

Thx,

fyr145

[Joe]

I'd be interested in your ride height sensors (both sides) if they are good and not broken (which looking at how clean your under carriage is I guess they are perfect ).

Just PM me if interested w.price

Thanks

[Egan]

Originally Posted by Joe

I'd be interested in your ride height sensors (both sides) if they are good and not broken (which looking at how clean your under carriage is I guess they are perfect ).

Just PM me if interested w.price

Thanks

I left these in place, so let me see if I can pull them out tomorrow. I'll check the service manual, but do you have a picture of what they look like / where they are.

[Joe]

If you look inside rear wheel wells towards front of truck you should see them. Looks like a little piston like thing attached to rear suspension and connected with a cable/plug. Mine are covered with an undercoating from previous owner but I think they simply bolt in with one or two bolts. I don't necessarily need the wiring harness from the sensors back but if you find its easy to take that out as well i'd be interested in it as well. Really just need the sensors themselves though.

[Egan]

Originally Posted by Joe

If you look inside rear wheel wells towards front of truck you should see them. Looks like a little piston like thing attached to rear suspension and connected with a cable/plug. Mine are covered with an undercoating from previous owner but I think they simply bolt in with one or two bolts. I don't necessarily need the wiring harness from the sensors back but if you find its easy to take that out as well i'd be interested in it as well. Really just need the sensors themselves though.

Got it. I'll take a look tomorrow when I have the truck back up in the air.

[Egan]

Originally Posted by Joe

If you look inside rear wheel wells towards front of truck you should see them. Looks like a little piston like thing attached to rear suspension and connected with a cable/plug. Mine are covered with an undercoating from previous owner but I think they simply bolt in with one or two bolts. I don't necessarily need the wiring harness from the sensors back but if you find its easy to take that out as well i'd be interested in it as well. Really just need the sensors themselves though.

I found them no problem, but I read that if I take them out I'll get a trouble light on the dash. Is there a way to avoid this?

[Egan]

Originally Posted by fyr145

I need the wiring at the compressor end that it plugs into. It looks like is a 24 pin connection and theres another smaller 2 pin connector near it as well. You show it in one of your pics that says you zip tied it to the rear bumper.

Do you still have the bolts to the compressor too, so that I can get mine mounted?

Let me how much shipping is and I can send you payment via Paypal.

Thx,

fyr145

If you need the wiring that goes from the harness I tied up under the bumper to the compressor & solenoid, I have that. I also have the nuts and bolts for the compressors (nuts&bolts for the front of each, nut only for the rear - there are studs built into the mounting plate).

Keep in mind that this is the 2 compressor setup.

Send me a PM with your zip and I'll get a freight quote.

[fyr145]

Originally Posted by Egan

If you need the wiring that goes from the harness I tied up under the bumper to the compressor & solenoid, I have that. I also have the nuts and bolts for the compressors (nuts&bolts for the front of each, nut only for the rear - there are studs built into the mounting plate).

Keep in mind that this is the 2 compressor setup.

Send me a PM with your zip and I'll get a freight quote.

PM sent